NEW GUI AVAILABLE
The proven EFLX Compiler is adding a Graphical User Interface based on customer demand.
The GUI features are available to customers in our production release AND our software evaluation license. Contact us at firstname.lastname@example.org for your software evaluation license for TSMC 16/28/40 with timing for multiple corners.
Phase 1 & 2 were released in Fall 2018 and are in use by multiple customers: Timing analyzer, Mapper, Floor Plan Builder and Placement Viewer.
Phase 3 and 4 are in development for release in mid to late Q1 2018.
AVAILABLE: FLOOR PLAN & PLACEMENT VIEWER
Here are a few screen shots to see a few highlights of the new features.
The Floor Planner allows a designer to quickly try out EFLX arrays, using a specific IP core (EFLX4K shown here), with different sizes and combinations of Logic/DSP.
Once an array is defined, RTL/Verilog can be synthesized and mapped to the array. The Placement Viewer shows the physical design by IP core and by RBB block within the core (color coding: green is MAC, magenta is RBB-M, gray is RBB-L; a pale color is an empty logic block).
There are multiple screens available for examining how blocks connect. Here are two examples.
The screen below examines the input and output connections of a given block in the design.
Then the screen below shows the block by block path from start to finish of a specific timing path (a timing path is the output of a flop to the input of another flop that goes through multiple logic stages).
The designer can easily switch between the various timing corners supported in the EFLX Compiler: for example, in 16nm we support 7 corners.
AVAILABLE: TIMING ANALYZER
Our new timing analyzer module allows you to see a histogram of all timing nets, then for each histogram bar to see the nets and then drill down into each net to see the stage by stage timing. This level of timing information aids in determining how to optimize your RTL for improving critical path worst case performance.
Timing is computed based on output files from Tempus/PrimeTime which describe every timing path through the EFLX core/array. Timing is available for each process node and for multiple corners for each process node (varying process conditions and voltages, not just worst case conditions).
Contact us for a demo and for a software evaluation license to try on your RTL: email@example.com.
Below are some details.
1st screen shows the 7 corners available for the TSMC 16FFC process. An EDIF netlist can be selected and a corner can be selected for optimizing place & route. Timing corners are available for all of the nominal voltages that TSMC supports: currently the 0.8V Tj nominal corners are populated (+/- 10%) and 1V corners for closing hold times. In the example below, an 8K LUT design will be placed and routed with timing optimized for SS, 0.72V and 125C.
After place and route, a timing histogram is generated showing the number of critical paths at each speed. The worst case performance for this example is 510.5MHz or 1959ps. In the GUI, using the cursor, the rightmost histogram bar was selected (1900-2000ps): the pop-up window shows there are two paths in this histogram.
Then, in this example, the 1959ps path is selected in the first pop-up window, which generates a 2nd pop-up window (see below) showing the 5% slowest paths in the logic cone of this path. Using this, a designer can see if one path is a lot worse than the others orin there a lot of similar paths.
Then, drilling down further, the designer can look at any of the paths in the logic cone (in the example below the 1946ps path is selected in the middle pop-up box). Once a path is selected, the designer can see every stage from the output of one flip flop through the various logic and net delays that make up the total path delay.
These data are based on silicon-sign-off data from Cadence Tempus, using TSMC cell libraries (CCS), wire load models (QRC), in the TSMC sign-off corners (e.g. SSGNP 0.72V, -40C RCworst-Ccworst-T, AOCV) following TSMC timing sign-off guidelines. The database of timing reports and SDF timing annotation is then parsed by the EFLX Compiler to perform timing-analysis on your design in each corner. This rigorous ASIC timing signoff method ensures your RTL running on the EFLX array will meet the EFLX Compiler timing the same way you designed your ASIC to meeting timing under worst-case conditions. Unlike other FPGA companies, no timing margins or derates needs to be added to our timing-analysis reports because we use the same methodology you do for the rest of your chip.
These timing tools can allow the designer to gather information which may allow them to optimize the RTL to improve performance. In a future phase of the GUI, the physical graph of the path through the array will also be observable.
GUI PHASE 3 & 4
In mid to late Q1, 2018 features will be added for I/O Mapping, Power Estimator and Logixizer/Debugger.
Synplify: this widely used Synopsys tool takes your netlist/RTL and breaks it down into primitives in an EDIF format, which feeds into the EFLX Compiler.
- Input your RTL to see the resources required: # LUTs/Cores, DSP blocks and RAM.
- Configure your EFLX array: select the number and type of EFLX cores, the clocks, the I/O configuration connecting the array to the SoC, and the type and amount of Block RAM.
- Input your RTL with your configured array to determine the worst case path and frequency for your target process.
- Generate the bit file (bit stream) that programs the EFLX array in the SoC to execute your RTL.
The EFLX Compiler is now in use at customers for designs and evaluation.
We can demonstrate our tools by Web-ex and run RTL for a customer, if they wish..
Here is a video demonstration of the key steps in compiling an RTL design for EFLX embedded FPGA to determine performance and LUT count. (the timing files vary by process node).
For qualified customers we can provide free evaluation licenses. Contact us at firstname.lastname@example.org.
[Synopsys is a Registered Trademark of Synposys, Inc.]